Candy CDI 3015-S Manuel d'utilisateur télécharger pdf (Page 11)

PROGRAMME SELECTION

AND SPECIAL FUNCTIONS

(Use in conjunction with programme guide)

IMPORTANT

The dishwasher has two very practical

functions:

- the "recommended" programme

(which is ideal for full load daily use)

for quick and accurate selection;

- the "Auto’ Memory", function saves

any programme used at least 3 times

consecutively, so that if you regularly

use the same washing cycle you

do not have to continually set the

programme thereby saving time and

effort.

Programme settings

■ Open the door and place the dirty dishes

inside the appliance.

■ Press the "ON/OFF" button .

■ After pressing the "ON/OFF" button,

the indicator light which is factory set at

"recommended”, or the indicator light

for the "Auto’ Memory" programme will

flash.

■ If you wish to select an option, press the

option button (the corresponding indicator

light will light up).

The option button can be selected or

deselected WITHIN 2 minutes of the

programme commencing.

■ Choose a programme by pressing the

corresponding button.

■ To start the programme, close the door.

IMPORTANT

To select the "COLD RINSE" programme,

simultaneously press the "RAPID"

programme button and "HALF LOAD"

option button.

Programme interruption

Opening the door when a programme is

running is not recommended especially

during the main wash and final hot rinse

phases. However, if the door is opened

while a programme is running (for example,

to add dishes) the machine stops

automatically.

Close the door, without pressing any

buttons. The cycle will start from where it

left off.

WARNING!

If you open the door during the

drying cycle, an audible audio signal

advises you that the drying cycle has

not yet finished.

Changing a running programme

Proceed as follows to change or cancel a

running program:

■ Open the door.

■ Hold down the current programme button

(with the indicator light on) for at least 5

seconds. The programme indicator lights

(except for the "RAPID" programme

indicator light) will flash.

■ The running programme will be cancelled

and the indicator light for the

“recommended” programme or the

indicator light for the programme that

was used at least 3 times consecutively

will start to flash.

■ At this point a new programme can be set.

IMPORTANT

To cancel the "COLD RINSE"

programme, simultaneously hold

down the "RAPID" programme button

and "HALF LOAD" option button.

WARNING!

Before starting a new programme,

you should check that there is still

detergent in the dispenser.

If necessary, top up the dispenser.

If there is any break in the power supply

while the dishwasher is operating, a

special memory stores the selected

programme and, when the power is

restored, it continues where it left off.

Programme operations

When a programme is running the relevant

indicator light will remain on and the 3

“PROGRAMME STATUS” indicator lights

("WASH" , "RINSE" , and "DRY" )

will light singularly and in sequence to

indicate the current phase.

Programme end

The “PROGRAMME STATUS” indicator

lights will turn off and the indicator light

which is factory set "recommended”, or

the indicator light for the Auto’ Memory

programme, will blink to indicate that the

cycle has ended.

Dishes can now be removed and the

dishwasher turned off by pressing the

"ON/OFF" button or dishes can be loaded

for new cycle.

Option button

"HALF LOAD" button

By using this option, it is possible to wash

a smaller quantity of crockery: you should

load only the upper basket for dishes and

place cutlery in the tray in the bottom

basket.

This reduces water and energy consumption

and requires a smaller quantity of

detergent.

"START DELAY" button

The dishwasher start time can be set with

this button, delaying the start by 3, 6 or 9

hours.

Proceed as follows to set a delayed start:

■ Press the "START DELAY" button (each

time the button is pressed the start

will be delayed by 3, 6 or 9 hours

respectively and the corresponding time

indicator light will illuminate).

■ To start the countdown, press the selected

programme button (the relevant indicator

light will come on, while the set time

indicator light will start to flash).

If a 9 hour delay is set, countdown will be

displayed by the 6h indicator light after 3

hours and the 3h indicator light after 6

hours.

At the end of the last 3 hours (at the end

of countdown) the 3h indicator light will

stop flashing and remain on to indicate the

washing phase and the programme will

start automatically.

If countdown has not ended, whereby

the programme has not yet started, it is

possible to change or cancel the delayed

start and select another programme or to

select/deselect the option button, proceeding

as follows:

■ Hold down the selected programme

button for at least 5 seconds. The

programme indicator lights (except for

the "RAPID" programme indicator light)

will flash.

■ The selected programme will be cancelled

and the indicator light for the

"recommended" programme or the

indicator light for the programme that

was used at least 3 times consecutively

will start to flash.

■ Press the "START DELAY" button to

set another delayed start time (the

corresponding indicator light will turn on).

■ A new programme can be set after a

delayed time has been changed or

cancelled or an option button has selected

or deselected.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 28 29

Commentaires sur ces manuels

Pas de commentaire

Candy CDI 3015-S Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Lave-vaisselle Candy CDI 3015-S